Are you currently trying to find critical information around A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily accessible, the job can move speedily; if you have to open a wall surface to eliminate the old bathtub and also place the new tub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the job and are comfortable trying it. Rather than working with a professional to take over a halfway-completed project, it is far better to take into consideration using one before you begin. Chances are you may require an expert plumber to make tube connections.
This article will help you install a brand-new tub in your restroom if you have actually already bought a brand-new tub as well as don't require to change the plan of your previous water supply pipelines.
Your tools as well as product checklist must comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of eliminating the existing taps can be quite bothersome because of the limited gain access to that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washing machines are in place between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost flexible faucet port to the suitable supply pipeline by making a compression join; then do the very same for the various other faucet.
Activate the water system and also check all joints and new pipework for leakages as well as tighten them if needed. Fill up the tub and likewise check the overflow outlet and the regular outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the manufacturer's user's manual. Tiling and securing around the bath tub should wait until the tub has actually been utilized at the very least when as this will certainly resolve it into its last position.
Preparing for the Installation
First of all, the sustaining frame supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bath fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, causing the water to permeate the wall in between the bathroom as well as the tiling, leading to issues with dampness as well as possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealer can fracture rather early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very fascinated by Tools You Need to Install a New Bathtub and I really hope you enjoyed reading the new article. You should take the time to share this blog post if you appreciated it. Thank-you for your time invested reading it.
Quality solution? Call.